*
2 Likes

Тема: MAG 250 проблема с прошивкой, Help!

Показано с 171 по 177 из 177

  1. #171
    Senior Member
    Регистрация 21.03.2015
    Сообщений 143


    Добрый день!
    Кто тут с Одессы?
    Меня интересует, возможно ли вернуть до заводского состояния, приставку от Веги?
  2. #172
    Member
    Регистрация 03.09.2012
    Сообщений 31
    Добрый день!
    Кто тут с Одессы?
    Меня интересует, возможно ли вернуть до заводского состояния, приставку от Веги?
    Да, возможно. Какие собственно проблемы?
  3. #173
    Junior Member
    Регистрация 12.05.2018
    Адрес Украина, Луганск
    Сообщений 2
    Добрый день!



    Приставка MAG 250 переодически несколько раз в день зависала, перезагрузка не помогала, через время включалась и работала пару минут и зависала. Теперь постоянно при включении горит Loading ... пробовал прошить как через USB так и через мультикаст, вылазит ошибка Error writing image to flash. Waiting operator command. В биосе поля Ver Bootst. Ver. Userfs пустые, я так понимаю реанимировать приставку без СЦ не удасться? умерла память или прошивка слетела?

    вот что удалось увидеть через UART, куда копать подскажет ктото?
    Spoiler

    Board: MAG250 [32-bit mode]


    U-Boot 1.3.1 (Nov 7 2011 - 20:45:09) - stm23_0047

    DRAM: 256 MiB
    NOR: 1 MiB
    NAND: 256 MiB
    In: serial
    Out: serial
    Err: serial
    Press "Menu" for enter menu
    Hit any key to stop autoboot: 0
    ### JFFS2 loading 'uImage' to 0x80000000
    Scanning JFFS2 FS: . done.
    ### JFFS2 load complete: 3230449 bytes loaded to 0x80000000
    ## Booting image at 80000000 ...
    Image Name: MAG250 SH4 Kernel Linux 2.6.17
    Image Type: SuperH Linux Kernel Image (gzip compressed)
    Data Size: 3230385 Bytes = 3.1 MiB
    Load Address: 80800000
    Entry Point: 80801000
    Verifying Checksum ... Bad Data CRC

    Warning: MAC addresses don't match:
    HW MAC address: FF:FF:FF:FF:FF:FF
    "ethaddr" value: 00:00:00:00:00:00

    sing MAC Address 00:00:00:00:00:00
    STM-GMAC: IC+ IP101 found
    STM-GMAC: PHY address mismatch with hardware (hw 8 != 1)
    STM-GMAC: PHY auto-negotiate timed out
    STM-GMAC: *Warning* no link detected
    BOOTP broadcast 1
    BOOTP broadcast 2
    BOOTP broadcast 3
    BOOTP broadcast 4
    BOOTP broadcast 5
    BOOTP broadcast 6
    BOOTP broadcast 7
    BOOTP broadcast 8
    BOOTP broadcast 9
    BOOTP broadcast 10
    Последний раз редактировалось Snake; 13.05.2018 в 22:34.
  4. #174
    Senior Member
    Регистрация 29.01.2013
    Сообщений 930
    было несколько лет назад,прошивать нужно начинать прошей от инфомира,получилось с 15 или с 20 раза с флешки через задний вход
  5. #175
    Junior Member
    Регистрация 12.05.2018
    Адрес Украина, Луганск
    Сообщений 2
    Вот такое вылазит еще, возможно NAND умер?
    Spoiler

    Board: MAG250 [32-bit mode]
    U-Boot 1.3.1 (Nov 7 2011 - 20:45:09) - stm23_0047
    DRAM: 256 MiB
    NOR: 1 MiB
    NAND: 256 MiB
    In: serial
    Out: serial
    Err: serial
    Press "Menu" for enter menu
    Loading image form multicast channel 224.50.0.70:9000 is started...

    Warning: MAC addresses don't match:
    HW MAC address: ***************
    "ethaddr" value: ****************
    Using MAC Address ******************
    STM-GMAC: IC+ IP101 found
    STM-GMAC: PHY address mismatch with hardware (hw 8 != 1)
    STM-GMAC: PHY auto-negotiate timed out
    STM-GMAC: *Warning* no link detected
    McloadStart
    *** Warning: no boot file name; using 'C0A8F3F9.img'
    Load from multicast group: IP - 224.50.0.70 Port - 9000
    Load address: 0x80000000
    Loading: *
    Starting receive image
    TTTTT
    Abort

    Error MC Upgrade!!!
    Loading image form multicast channel 224.50.0.70:9000 is started...

    Warning: MAC addresses don't match:
    HW MAC address: ***************
    "ethaddr" value: ***************
    Using MAC Address ****************
    STM-GMAC: IC+ IP101 found
    STM-GMAC: PHY address mismatch with hardware (hw 8 != 1)
    STM-GMAC: 100Mbs full duplex link detected
    McloadStart
    *** Warning: no boot file name; using 'C0A8F3F9.img'
    Load from multicast group: IP - 224.50.0.70 Port - 9000
    Load address: 0x80000000
    Loading: *
    Starting receive image
    TTTTTMcloadStart
    *** Warning: no boot file name; using 'C0A8F3F9.img'
    Load from multicast group: IP - 224.50.0.70 Port - 9000
    Load address: 0x80000000
    Loading: *
    Starting receive image
    TTTT############################################## ###################
    ################################################## ###############
    ################################################## ###############
    ################################################## ###############
    ################################################## ###############
    ################################################## ###############
    ################################################## ###############
    ##############
    End receive image
    Bytes transferred = 6378399 (61539f hex)
    ## Booting image at 80000000 ...
    Image Name: SH4 MAG250 Bootstrap Ver:002
    Image Type: SH-4 Linux Kernel Image (uncompressed)
    Data Size: 6378335 Bytes = 6.1 MiB
    Load Address: 80800000
    Entry Point: 80801000
    Verifying Checksum ... OK
    Read data: 80000040 length: 875 (0x36b)
    Signature OK!!
    Signature OK!!
    OK

    Starting kernel nwhwconf=device:eth0,hwaddr:00:1a:79:0e:21:da root=/dev/mtdblock6 rootfstype=jffs2 mem=160m bigphysarea=2048 ip=none mcman=on mtdparts=stm-nand-flex.1:4M(Kernel),120M(RootFs),4M(Kernel2),120M(Ro otFs2),-(Userfs) console=ttyAS0,115200 - 0x00000000 - 0 ...

    Linux version 2.6.23.17_stm23_A23-MAG250_7105 (root@Server01.localdomain) (gcc version 4.2.4 (snapshot) (STMicroelectronics/Linux Base 4.2.4-44)) #2 PREEMPT Thu Jun 8 17:00:37 EEST 2017
    Booting machvec: mag250
    Node 0: start_pfn = 0x40000, low = 0x4f800
    Zone PFN ranges:
    Normal 262144 -> 325632
    Movable zone start PFN for each node
    early_node_map[1] active PFN ranges
    0: 262144 -> 325632
    Infomir,LLC MAG250 board initialisation
    STx7105 version 4.x
    Built 1 zonelists in Zone order. Total pages: 62992
    Kernel command line: nwhwconf=device:eth0,hwaddr:00:1a:79:0e:21:da root=/dev/mtdblock6 rootfstype=jffs2 mem=160m bigphysarea=2048 ip=none mcman=on mtdparts=stm-nand-flex.1:4M(Kernel),120M(RootFs),4M(Kernel2),120M(Ro otFs2),-(Userfs) console=ttyAS0,115200
    bpa2: partition 'bigphysarea' created at 0x41031000, size 8192 kB (0x00800000 B)
    PID hash table entries: 1024 (order: 10, 4096 bytes)
    Using tmu for system timer
    Using 25.000 MHz high precision timer.
    Console: colour dummy device 80x25
    console [ttyAS0] enabled
    Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    Memory: 228864k/253952k available (3095k kernel code, 740k data, 2384k init)
    PVR=04909200 CVR=60880000 PRR=00009e40
    I-cache : n_ways=2 n_sets=512 way_incr=16384
    I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
    D-cache : n_ways=2 n_sets=512 way_incr=16384
    D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
    Mount-cache hash table entries: 512
    CPU: STx7105
    NET: Registered protocol family 16
    Configuring FLASH for boot-from-NOR
    Generic PHY: Registered new driver
    SCSI subsystem initialized
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    Time: SuperH clocksource has been installed.
    NET: Registered protocol family 2
    IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
    TCP established hash table entries: 8192 (order: 4, 65536 bytes)
    TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
    TCP: Hash tables configured (established 8192 bind 8192)
    TCP reno registered
    NTFS driver 2.1.28 [Flags: R/W].
    JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
    fuse init (API version 7.
    JFS: nTxBlock = 1788, nTxLock = 14311
    io scheduler noop registered
    io scheduler anticipatory registered (default)
    io scheduler deadline registered
    io scheduler cfq registered
    STMicroelectronics ASC driver initialized
    stasc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stasc
    stasc.1: ttyAS1 at MMIO 0xfd031000 (irq = 122) is a stasc
    RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
    platform registration... <7>done!
    GMAC - user ID: 0x10, Synopsys ID: 0x33
    eth0 - (dev. name: stmmaceth - id: 0, IRQ #134
    IO base addr: 0xfd110000)
    STMMAC MII Bus: probed
    eth0: PHY ID 02430c54 at 1 IRQ -1 (0:01) active
    ICPlus IP101A: Registered new driver
    ICPlus IP1001: Registered new driver
    ICPlus IP175C: Registered new driver
    physmap platform flash device: 00100000 at 00000000
    physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
    Amd/Fujitsu Extended Query Table at 0x0040
    physmap-flash: Swapping erase regions for broken CFI table.
    number of CFI chips: 1
    cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
    RedBoot partition parsing not available
    Using physmap partition information
    Creating 5 MTD partitions on "physmap-flash":
    0x00000000-0x00050000 : "BootLoader"
    first erase region 0 for slave @ 0
    0x00050000-0x000a0000 : "Upgrade Boot"
    first erase region 0 for slave @ 327680
    0x000a0000-0x000e0000 : "User's FS"
    first erase region 0 for slave @ 655360
    0x000e0000-0x000f0000 : "Logo"
    first erase region 0 for slave @ 917504
    0x000f0000-0x00100000 : "BootLoader Enviroment"
    first erase region 1 for slave @ 983040
    stm-ehci stm-ehci.0: st-ehci
    stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
    stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00
    stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 1 port detected
    stm-ohci stm-ohci.0: stm-ohci
    stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
    stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 1 port detected
    stm-ehci stm-ehci.1: st-ehci
    stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3
    stm-ehci stm-ehci.1: irq 143, io mem 0xfeaffe00
    stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 1 port detected
    stm-ohci stm-ohci.1: stm-ohci
    stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4
    stm-ohci stm-ohci.1: irq 142, io mem 0xfeaffc00
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 1 port detected
    Initializing USB Mass Storage driver...
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    mice: PS/2 mouse device common for all mice
    i2c /dev entries driver
    usbcore: registered new interface driver usbhid
    drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
    STMicroelectronics - Coprocessors st231 Init
    st-coprocessor-0: No RAM reserved
    st231.0 Coprocessor -------------------------------------------
    not configured!
    ---------------------------------------------------------------
    st-coprocessor-1: No RAM reserved
    st231.1 Coprocessor -------------------------------------------
    not configured!
    ---------------------------------------------------------------
    stm_rng hardware driver 1.0 configured
    TCP cubic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    Freeing unused kernel memoryzroute: SIOCADDRT: Network is down
    net.core.rmem_max = 1000000
    Starting S20uhdcp...
    check_usbman:
    check_mcman:mcman=on
    ## Error: "update_url" not defined
    ## Error: "mcip_img_conf" not defined
    ## Error: "mcport_img_conf" not defined
    mcip_img=224.50.0.51
    mcport_img=9001
    ## Error: "oppubKEY" not defined
    Print recv_start to Monitor
    PHY: 0:01 - Link is Up - 100/Full
    Sat Jan 1 00:00:02 UTC 2000
    IP: 192.168.243.249
    MAC: ***********
    Wrong offset in file /usr/bin/radix64.KEY -263 0

    Signature not correct
    Error: Not correct digital signature operator's key
    Use default operator's keys
    Connect to IP:224.50.0.51 port:9001
    Create new file. File size:74600074
    SN 0 offs 432480
    Print recv_success to Monitor
    Start Write Image to nand flash
    4096+0 records in
    4096+0 records out
    NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
    Scanning device for bad blocks
    Bad eraseblock 0 at 0x00000000
    Bad eraseblock 3 at 0x00060000
    Bad eraseblock 8 at 0x00100000
    Bad eraseblock 9 at 0x00120000
    Bad eraseblock 10 at 0x00140000
    Bad eraseblock 11 at 0x00160000
    Bad eraseblock 16 at 0x00200000
    Bad eraseblock 17 at 0x00220000
    Bad eraseblock 18 at 0x00240000
    Bad eraseblock 19 at 0x00260000
    Bad eraseblock 24 at 0x00300000
    Bad eraseblock 25 at 0x00320000
    Bad eraseblock 26 at 0x00340000
    Bad eraseblock 27 at 0x00360000
    Bad eraseblock 32 at 0x00400000
    Bad eraseblock 33 at 0x00420000
    Bad eraseblock 34 at 0x00440000
    Bad eraseblock 35 at 0x00460000
    Bad eraseblock 40 at 0x00500000
    Bad eraseblock 41 at 0x00520000
    Bad eraseblock 43 at 0x00560000
    Bad eraseblock 48 at 0x00600000
    Bad eraseblock 49 at 0x00620000
    Bad eraseblock 50 at 0x00640000
    Bad eraseblock 51 at 0x00660000
    Bad eraseblock 56 at 0x00700000
    Bad eraseblock 57 at 0x00720000
    Bad eraseblock 58 at 0x00740000
    Bad eraseblock 59 at 0x00760000
    Bad eraseblock 64 at 0x00800000
    Bad eraseblock 65 at 0x00820000
    Bad eraseblock 66 at 0x00840000
    Bad eraseblock 67 at 0x00860000
    Bad eraseblock 72 at 0x00900000
    Bad eraseblock 83 at 0x00a60000
    Bad eraseblock 282 at 0x02340000
    Bad eraseblock 283 at 0x02360000
    Bad eraseblock 380 at 0x02f80000
    Bad eraseblock 497 at 0x03e20000
    Bad eraseblock 537 at 0x04320000
    Bad eraseblock 538 at 0x04340000
    5 cmdlinepart partitions found on MTD device stm-nand-flex.1
    Creating 5 MTD partitions on "stm-nand-flex.1":
    0x00000000-0x00400000 : "Kernel"
    0x00400000-0x07c00000 : "RootFs"
    0x07c00000-0x08000000 : "Kernel2"
    0x08000000-0x0f800000 : "RootFs2"
    0x0f800000-0x10000000 : "Userfs"
    Bad block at 0, 1 block(s) from 0 will be skipped
    Bad block at 60000, 1 block(s) from 60000 will be skipped
    Bad block at 100000, 1 block(s) from 100000 will be skipped
    Bad block at 120000, 1 block(s) from 120000 will be skipped
    Bad block at 140000, 1 block(s) from 140000 will be skipped
    Bad block at 160000, 1 block(s) from 160000 will be skipped
    Bad block at 200000, 1 block(s) from 200000 will be skipped
    Bad block at 220000, 1 block(s) from 220000 will be skipped
    Bad block at 240000, 1 block(s) from 240000 will be skipped
    Bad block at 260000, 1 block(s) from 260000 will be skipped
    Bad block at 300000, 1 block(s) from 300000 will be skipped
    Bad block at 320000, 1 block(s) from 320000 will be skipped
    Bad block at 340000, 1 block(s) from 340000 will be skipped
    Bad block at 360000, 1 block(s) from 360000 will be skipped
    Data did not fit into device, due to bad blocks
    : Inappropriate ioctl for device
    /usr/bin/img_write.sh: line 245: //: Permission denied
    Bad block at 0, 1 block(s) from 0 will be skipped
    Bad block at 60000, 1 block(s) from 60000 will be skipped
    Bad block at 100000, 1 block(s) from 100000 will be skipped
    Bad block at 120000, 1 block(s) from 120000 will be skipped
    Bad block at 140000, 1 block(s) from 140000 will be skipped
    Bad block at 160000, 1 block(s) from 160000 will be skipped
    Bad block at 200000, 1 block(s) from 200000 will be skipped
    Bad block at 220000, 1 block(s) from 220000 will be skipped
    Bad block at 240000, 1 block(s) from 240000 will be skipped
    Bad block at 260000, 1 block(s) from 260000 will be skipped
    Bad block at 300000, 1 block(s) from 300000 will be skipped
    Bad block at 320000, 1 block(s) from 320000 will be skipped
    Bad block at 340000, 1 block(s) from 340000 will be skipped
    Bad block at 360000, 1 block(s) from 360000 will be skipped
    Data did not fit into device, due to bad blocks
    : Inappropriate ioctl for device
    Print write_error to Monitor
    Wait command from operator
    Log ip parameters must be set
    Connect to IP: port:0
    Последний раз редактировалось Snake; 13.05.2018 в 22:34.
  6. #176
    Senior Member
    Регистрация 10.12.2013
    Сообщений 965
    Вот такое вылазит еще, возможно NAND умер?
    Spoiler

    Board: MAG250 [32-bit mode]
    U-Boot 1.3.1 (Nov 7 2011 - 20:45:09) - stm23_0047
    DRAM: 256 MiB
    NOR: 1 MiB
    NAND: 256 MiB
    In: serial
    Out: serial
    Err: serial
    Press "Menu" for enter menu
    Loading image form multicast channel 224.50.0.70:9000 is started...

    Warning: MAC addresses don't match:
    HW MAC address: ***************
    "ethaddr" value: ****************
    Using MAC Address ******************
    STM-GMAC: IC+ IP101 found
    STM-GMAC: PHY address mismatch with hardware (hw 8 != 1)
    STM-GMAC: PHY auto-negotiate timed out
    STM-GMAC: *Warning* no link detected
    McloadStart
    *** Warning: no boot file name; using 'C0A8F3F9.img'
    Load from multicast group: IP - 224.50.0.70 Port - 9000
    Load address: 0x80000000
    Loading: *
    Starting receive image
    TTTTT
    Abort

    Error MC Upgrade!!!
    Loading image form multicast channel 224.50.0.70:9000 is started...

    Warning: MAC addresses don't match:
    HW MAC address: ***************
    "ethaddr" value: ***************
    Using MAC Address ****************
    STM-GMAC: IC+ IP101 found
    STM-GMAC: PHY address mismatch with hardware (hw 8 != 1)
    STM-GMAC: 100Mbs full duplex link detected
    McloadStart
    *** Warning: no boot file name; using 'C0A8F3F9.img'
    Load from multicast group: IP - 224.50.0.70 Port - 9000
    Load address: 0x80000000
    Loading: *
    Starting receive image
    TTTTTMcloadStart
    *** Warning: no boot file name; using 'C0A8F3F9.img'
    Load from multicast group: IP - 224.50.0.70 Port - 9000
    Load address: 0x80000000
    Loading: *
    Starting receive image
    TTTT############################################## ###################
    ################################################## ###############
    ################################################## ###############
    ################################################## ###############
    ################################################## ###############
    ################################################## ###############
    ################################################## ###############
    ##############
    End receive image
    Bytes transferred = 6378399 (61539f hex)
    ## Booting image at 80000000 ...
    Image Name: SH4 MAG250 Bootstrap Ver:002
    Image Type: SH-4 Linux Kernel Image (uncompressed)
    Data Size: 6378335 Bytes = 6.1 MiB
    Load Address: 80800000
    Entry Point: 80801000
    Verifying Checksum ... OK
    Read data: 80000040 length: 875 (0x36b)
    Signature OK!!
    Signature OK!!
    OK

    Starting kernel nwhwconf=device:eth0,hwaddr:00:1a:79:0e:21:da root=/dev/mtdblock6 rootfstype=jffs2 mem=160m bigphysarea=2048 ip=none mcman=on mtdparts=stm-nand-flex.1:4M(Kernel),120M(RootFs),4M(Kernel2),120M(Ro otFs2),-(Userfs) console=ttyAS0,115200 - 0x00000000 - 0 ...

    Linux version 2.6.23.17_stm23_A23-MAG250_7105 (root@Server01.localdomain) (gcc version 4.2.4 (snapshot) (STMicroelectronics/Linux Base 4.2.4-44)) #2 PREEMPT Thu Jun 8 17:00:37 EEST 2017
    Booting machvec: mag250
    Node 0: start_pfn = 0x40000, low = 0x4f800
    Zone PFN ranges:
    Normal 262144 -> 325632
    Movable zone start PFN for each node
    early_node_map[1] active PFN ranges
    0: 262144 -> 325632
    Infomir,LLC MAG250 board initialisation
    STx7105 version 4.x
    Built 1 zonelists in Zone order. Total pages: 62992
    Kernel command line: nwhwconf=device:eth0,hwaddr:00:1a:79:0e:21:da root=/dev/mtdblock6 rootfstype=jffs2 mem=160m bigphysarea=2048 ip=none mcman=on mtdparts=stm-nand-flex.1:4M(Kernel),120M(RootFs),4M(Kernel2),120M(Ro otFs2),-(Userfs) console=ttyAS0,115200
    bpa2: partition 'bigphysarea' created at 0x41031000, size 8192 kB (0x00800000 B)
    PID hash table entries: 1024 (order: 10, 4096 bytes)
    Using tmu for system timer
    Using 25.000 MHz high precision timer.
    Console: colour dummy device 80x25
    console [ttyAS0] enabled
    Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    Memory: 228864k/253952k available (3095k kernel code, 740k data, 2384k init)
    PVR=04909200 CVR=60880000 PRR=00009e40
    I-cache : n_ways=2 n_sets=512 way_incr=16384
    I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
    D-cache : n_ways=2 n_sets=512 way_incr=16384
    D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
    Mount-cache hash table entries: 512
    CPU: STx7105
    NET: Registered protocol family 16
    Configuring FLASH for boot-from-NOR
    Generic PHY: Registered new driver
    SCSI subsystem initialized
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    Time: SuperH clocksource has been installed.
    NET: Registered protocol family 2
    IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
    TCP established hash table entries: 8192 (order: 4, 65536 bytes)
    TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
    TCP: Hash tables configured (established 8192 bind 8192)
    TCP reno registered
    NTFS driver 2.1.28 [Flags: R/W].
    JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
    fuse init (API version 7.
    JFS: nTxBlock = 1788, nTxLock = 14311
    io scheduler noop registered
    io scheduler anticipatory registered (default)
    io scheduler deadline registered
    io scheduler cfq registered
    STMicroelectronics ASC driver initialized
    stasc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stasc
    stasc.1: ttyAS1 at MMIO 0xfd031000 (irq = 122) is a stasc
    RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
    platform registration... <7>done!
    GMAC - user ID: 0x10, Synopsys ID: 0x33
    eth0 - (dev. name: stmmaceth - id: 0, IRQ #134
    IO base addr: 0xfd110000)
    STMMAC MII Bus: probed
    eth0: PHY ID 02430c54 at 1 IRQ -1 (0:01) active
    ICPlus IP101A: Registered new driver
    ICPlus IP1001: Registered new driver
    ICPlus IP175C: Registered new driver
    physmap platform flash device: 00100000 at 00000000
    physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
    Amd/Fujitsu Extended Query Table at 0x0040
    physmap-flash: Swapping erase regions for broken CFI table.
    number of CFI chips: 1
    cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
    RedBoot partition parsing not available
    Using physmap partition information
    Creating 5 MTD partitions on "physmap-flash":
    0x00000000-0x00050000 : "BootLoader"
    first erase region 0 for slave @ 0
    0x00050000-0x000a0000 : "Upgrade Boot"
    first erase region 0 for slave @ 327680
    0x000a0000-0x000e0000 : "User's FS"
    first erase region 0 for slave @ 655360
    0x000e0000-0x000f0000 : "Logo"
    first erase region 0 for slave @ 917504
    0x000f0000-0x00100000 : "BootLoader Enviroment"
    first erase region 1 for slave @ 983040
    stm-ehci stm-ehci.0: st-ehci
    stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
    stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00
    stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 1 port detected
    stm-ohci stm-ohci.0: stm-ohci
    stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
    stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 1 port detected
    stm-ehci stm-ehci.1: st-ehci
    stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3
    stm-ehci stm-ehci.1: irq 143, io mem 0xfeaffe00
    stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 1 port detected
    stm-ohci stm-ohci.1: stm-ohci
    stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4
    stm-ohci stm-ohci.1: irq 142, io mem 0xfeaffc00
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 1 port detected
    Initializing USB Mass Storage driver...
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    mice: PS/2 mouse device common for all mice
    i2c /dev entries driver
    usbcore: registered new interface driver usbhid
    drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
    STMicroelectronics - Coprocessors st231 Init
    st-coprocessor-0: No RAM reserved
    st231.0 Coprocessor -------------------------------------------
    not configured!
    ---------------------------------------------------------------
    st-coprocessor-1: No RAM reserved
    st231.1 Coprocessor -------------------------------------------
    not configured!
    ---------------------------------------------------------------
    stm_rng hardware driver 1.0 configured
    TCP cubic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    Freeing unused kernel memoryzroute: SIOCADDRT: Network is down
    net.core.rmem_max = 1000000
    Starting S20uhdcp...
    check_usbman:
    check_mcman:mcman=on
    ## Error: "update_url" not defined
    ## Error: "mcip_img_conf" not defined
    ## Error: "mcport_img_conf" not defined
    mcip_img=224.50.0.51
    mcport_img=9001
    ## Error: "oppubKEY" not defined
    Print recv_start to Monitor
    PHY: 0:01 - Link is Up - 100/Full
    Sat Jan 1 00:00:02 UTC 2000
    IP: 192.168.243.249
    MAC: ***********
    Wrong offset in file /usr/bin/radix64.KEY -263 0

    Signature not correct
    Error: Not correct digital signature operator's key
    Use default operator's keys
    Connect to IP:224.50.0.51 port:9001
    Create new file. File size:74600074
    SN 0 offs 432480
    Print recv_success to Monitor
    Start Write Image to nand flash
    4096+0 records in
    4096+0 records out
    NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
    Scanning device for bad blocks
    Bad eraseblock 0 at 0x00000000
    Bad eraseblock 3 at 0x00060000
    Bad eraseblock 8 at 0x00100000
    Bad eraseblock 9 at 0x00120000
    Bad eraseblock 10 at 0x00140000
    Bad eraseblock 11 at 0x00160000
    Bad eraseblock 16 at 0x00200000
    Bad eraseblock 17 at 0x00220000
    Bad eraseblock 18 at 0x00240000
    Bad eraseblock 19 at 0x00260000
    Bad eraseblock 24 at 0x00300000
    Bad eraseblock 25 at 0x00320000
    Bad eraseblock 26 at 0x00340000
    Bad eraseblock 27 at 0x00360000
    Bad eraseblock 32 at 0x00400000
    Bad eraseblock 33 at 0x00420000
    Bad eraseblock 34 at 0x00440000
    Bad eraseblock 35 at 0x00460000
    Bad eraseblock 40 at 0x00500000
    Bad eraseblock 41 at 0x00520000
    Bad eraseblock 43 at 0x00560000
    Bad eraseblock 48 at 0x00600000
    Bad eraseblock 49 at 0x00620000
    Bad eraseblock 50 at 0x00640000
    Bad eraseblock 51 at 0x00660000
    Bad eraseblock 56 at 0x00700000
    Bad eraseblock 57 at 0x00720000
    Bad eraseblock 58 at 0x00740000
    Bad eraseblock 59 at 0x00760000
    Bad eraseblock 64 at 0x00800000
    Bad eraseblock 65 at 0x00820000
    Bad eraseblock 66 at 0x00840000
    Bad eraseblock 67 at 0x00860000
    Bad eraseblock 72 at 0x00900000
    Bad eraseblock 83 at 0x00a60000
    Bad eraseblock 282 at 0x02340000
    Bad eraseblock 283 at 0x02360000
    Bad eraseblock 380 at 0x02f80000
    Bad eraseblock 497 at 0x03e20000
    Bad eraseblock 537 at 0x04320000
    Bad eraseblock 538 at 0x04340000
    5 cmdlinepart partitions found on MTD device stm-nand-flex.1
    Creating 5 MTD partitions on "stm-nand-flex.1":
    0x00000000-0x00400000 : "Kernel"
    0x00400000-0x07c00000 : "RootFs"
    0x07c00000-0x08000000 : "Kernel2"
    0x08000000-0x0f800000 : "RootFs2"
    0x0f800000-0x10000000 : "Userfs"
    Bad block at 0, 1 block(s) from 0 will be skipped
    Bad block at 60000, 1 block(s) from 60000 will be skipped
    Bad block at 100000, 1 block(s) from 100000 will be skipped
    Bad block at 120000, 1 block(s) from 120000 will be skipped
    Bad block at 140000, 1 block(s) from 140000 will be skipped
    Bad block at 160000, 1 block(s) from 160000 will be skipped
    Bad block at 200000, 1 block(s) from 200000 will be skipped
    Bad block at 220000, 1 block(s) from 220000 will be skipped
    Bad block at 240000, 1 block(s) from 240000 will be skipped
    Bad block at 260000, 1 block(s) from 260000 will be skipped
    Bad block at 300000, 1 block(s) from 300000 will be skipped
    Bad block at 320000, 1 block(s) from 320000 will be skipped
    Bad block at 340000, 1 block(s) from 340000 will be skipped
    Bad block at 360000, 1 block(s) from 360000 will be skipped
    Data did not fit into device, due to bad blocks
    : Inappropriate ioctl for device
    /usr/bin/img_write.sh: line 245: //: Permission denied
    Bad block at 0, 1 block(s) from 0 will be skipped
    Bad block at 60000, 1 block(s) from 60000 will be skipped
    Bad block at 100000, 1 block(s) from 100000 will be skipped
    Bad block at 120000, 1 block(s) from 120000 will be skipped
    Bad block at 140000, 1 block(s) from 140000 will be skipped
    Bad block at 160000, 1 block(s) from 160000 will be skipped
    Bad block at 200000, 1 block(s) from 200000 will be skipped
    Bad block at 220000, 1 block(s) from 220000 will be skipped
    Bad block at 240000, 1 block(s) from 240000 will be skipped
    Bad block at 260000, 1 block(s) from 260000 will be skipped
    Bad block at 300000, 1 block(s) from 300000 will be skipped
    Bad block at 320000, 1 block(s) from 320000 will be skipped
    Bad block at 340000, 1 block(s) from 340000 will be skipped
    Bad block at 360000, 1 block(s) from 360000 will be skipped
    Data did not fit into device, due to bad blocks
    : Inappropriate ioctl for device
    Print write_error to Monitor
    Wait command from operator
    Log ip parameters must be set
    Connect to IP: port:0
    Да. Память убита.
    Последний раз редактировалось Snake; 13.05.2018 в 22:34.
  7. #177
    Member
    Регистрация 16.09.2009
    Сообщений 35
    Купил МАГ 250 на eBay. Пол-дня проморочился с откатом на старую, до мая 2017 прошивку.
    Стоит самая новая, декабрь 2017. С ней не идёт Совок ТВ. На сайте Совок ТВ пишут об откате.
    Пробовал загрузить с флешки, как из БИОС, так и из "Обновление ПО". Результаты странные.
    Переключился на mcast_v2.0. Вроде всё загружается, есть сообщение о успешной загрузке, но потом появляется сообщение Reception of an image is started!, которое висит очень долго.
    Есть подозрение на битые файлы. Где скачать рабочие прошу 0.2.18-r14, 0.2.18-r17 или 0.2.18-r18? Спасибо.

Ваши права

  • Вы не можете создавать новые темы
  • Вы не можете отвечать в темах
  • Вы не можете прикреплять вложения
  • Вы не можете редактировать свои сообщения