IPTV.ONLINE
13 Likes

Тема: MAG 322

Показано с 61 по 70 из 100

  1. #61
    Junior Member
    Регистрация 03.09.2018
    Сообщений 8


    Нашел точки UART. Прервать загрузку не дает, в конце просит логин и пароль. Стандартные не подходят.
    Вот лог загрузки:
    BCM07584500
    SLBS... done.
    M0C
    PSSBL. size:00067F40
    DZS
    L2=1
    LLMB=1
    BrCfg=E30FB7C6
    #@

    BCM975839A0 CFE v16.4, Endian Mode: Little
    Build Date: Fri Jan 12 14:08:20 EET 2018 (alever@alever-build)
    Copyright (C) Broadcom Corporation.

    Setting SPI Flash selection to: internal(onboard).
    Enabling NAND flash at CS2: TC58NVG2S0(DEVICE ID=0x98DC9026), ECC Level=12, Spare Area Size=32
    ISSI SPI flash detected: spi_lookup_device_type, mem_type = 60, mem_density = 16
    Size = 4MB, Sector Size 65536, Page Size 256
    WiFi module function: ON.
    CVBS Audio output: OFF.
    Button '4sec RESET' function: DISABLED.
    Polled button state: RELEASED.

    CPU speed: 742MHz
    DDR Frequency: 796 MHz
    DDR Mode: DDR3
    Total memory(MEMC 0): 512MB
    MEMC 0 DDR Width: 16
    Boot Device: SPI
    Total flash: 4MB
    RTS VERSION: Initial RTS Version
    ETH0_PHY: INT
    ETH0_MDIO_MODE: 1
    ETH0_SPEED: 100
    ETH0_PHYADDR: 1

    Initializing USB.

    CFE initialized.
    Starting splash screen.
    No valid image found in flash0.logo - continue splash

    Executing boot -z -elf nandflash0.Kernel2: 'bmem=82M@64M bmem=192M@512M ubi.mtd=3 rootfstype=ubifs root=ubi0_1 mtdparts=brcmnand.0:16M@0(Kernel),16M@16M(Kernel2) ,480M@32M(raw);spi0.0:1M@0(bootloader),1M@1M(secbo otloader),128K@2M(env),64KLoader:elf Filesys:raw Dev:nandflash0.Kernel2 File: Options:bmem=82M@64M bmem=192M@512M ubi.mtd=3 rootfstype=ubifs root=ubi0_1 mtdparts=brcmnand.0:16M@0(Kernel),16M@16M(Kernel2) ,480M@32M(raw);spi0.0:1M@0(bootloader),1M@1M(secbo otloader),128K@2M(env),64K@2176K(nvram),256K@2240K (logo),1600K@2496K(userfs) bootmedia=bank1
    Loading: Failure during reading from NAND partition: can't find good blocks in partition.
    No operator's key found in Firmware environment.
    Bad Digital Signature!!!
    Failed.
    Could not load : File not found
    Trying again with '-nz' option
    Loading: Failed.
    Could not load : File not found
    Executing boot -z -elf nandflash0.Kernel: 'bmem=82M@64M bmem=192M@512M ubi.mtd=3 rootfstype=ubifs root=ubi0_0 mtdparts=brcmnand.0:16M@0(Kernel),16M@16M(Kernel2) ,480M@32M(raw);spi0.0:1M@0(bootloader),1M@1M(secbo otloader),128K@2M(env),64K@Loader:elf Filesys:raw Dev:nandflash0.Kernel File: Options:bmem=82M@64M bmem=192M@512M ubi.mtd=3 rootfstype=ubifs root=ubi0_0 mtdparts=brcmnand.0:16M@0(Kernel),16M@16M(Kernel2) ,480M@32M(raw);spi0.0:1M@0(bootloader),1M@1M(secbo otloader),128K@2M(env),64K@2176K(nvram),256K@2240K (logo),1600K@2496K(userfs) bootmedia=bank0 fallbackstate=bank0
    Loading: No operator's key found in Firmware environment.
    Good Digital Signature.
    0x80001000/10613760 0x80a20400/110928 Entry address is 0x804a8000
    Starting program at 0x804a8000

    [ 0.000000] Linux version 3.3.8-4.1-g9a4e40f (alever@alever-build) (gcc version 4.5.4 (Broadcom stbgcc-4.5.4-2.9) ) #11 SMP Mon Dec 18 14:23:39 EET 2017
    [ 0.000000] Fetching vars from bootloader... found 12 vars.
    [ 0.000000] Options: moca=0 sata=0 pcie=0 usb=1
    [ 0.000000] board_pinmux_setup: Assuming pin assignment for: MAG325 .
    [ 0.000000] Using 512 MB + 0 MB RAM (from CFE)
    [ 0.000000] bootconsole [early0] enabled
    [ 0.000000] CPU revision is: 0002a065 (Broadcom BMIPS4380)
    [ 0.000000] FPU revision is: 00130001
    [ 0.000000] Determined physical RAM map:
    [ 0.000000] memory: 10000000 @ 00000000 (usable)
    [ 0.000000] memory: 10000000 @ 20000000 (usable)
    [ 0.000000] bmem: adding 82 MB RESERVED region at 64 MB (0x05200000@0x04000000)
    [ 0.000000] bmem: adding 192 MB RESERVED region at 512 MB (0x0c000000@0x20000000)
    [ 0.000000] bootmem_init: mapstart=0x00000a3c, bootmap_size=0x00006000
    [ 0.000000] Initrd not found or empty - disabling initrd
    [ 0.000000] Zone PFN ranges:
    [ 0.000000] Normal 0x00000000 -> 0x00030000
    [ 0.000000] Movable zone start PFN for each node
    [ 0.000000] Early memory PFN ranges
    [ 0.000000] 0: 0x00000000 -> 0x00010000
    [ 0.000000] 0: 0x00020000 -> 0x00030000
    [ 0.000000] PERCPU: Embedded 7 pages/cpu @81606000 s5120 r8192 d15360 u32768
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536
    [ 0.000000] Kernel command line: bmem=82M@64M bmem=192M@512M ubi.mtd=3 rootfstype=ubifs root=ubi0_0 mtdparts=brcmnand.0:16M@0(Kernel),16M@16M(Kernel2) ,480M@32M(raw);spi0.0:1M@0(bootloader),1M@1M(secbo otloader),128K@2M(env),64K@2176K(nvram),256K@2240K (logo),1600K@2496K(userfs) bootmedia=bank0 fallbackstate=bank0
    [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
    [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    [ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
    [ 0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
    [ 0.000000] Memory: 226604k/524288k available (4852k kernel code, 297684k reserved, 1210k data, 4304k init, 0k highmem)
    [ 0.000000] Hierarchical RCU implementation.
    [ 0.000000] NR_IRQS:160
    [ 0.000000] Measuring MIPS counter frequency...
    [ 0.000000] Detected MIPS clock frequency: 742 MHz (371.262 MHz counter)
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.001000] Calibrating delay loop... 741.37 BogoMIPS (lpj=37068
    [ 0.012000] pid_max: default: 32768 minimum: 301
    [ 0.013000] Mount-cache hash table entries: 512
    [ 0.015000] SMP: Booting CPU1...
    [ 0.020000] CPU revision is: 0002a065 (Broadcom BMIPS4380)
    [ 0.020000] FPU revision is: 00130001
    [ 0.020000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
    [ 0.020000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
    [ 0.029000] SMP: CPU1 is running
    [ 0.029000] Brought up 2 CPUs
    [ 0.030000] devtmpfs: initialized
    [ 0.033000] NET: Registered protocol family 16
    [ 0.034000] USB0: power enable is active low; overcurrent is active low
    [ 0.035000] platform_devices_setup: Registered platform driver&device for: WiFi-Module
    [ 0.039000] bio: create slab <bio-0> at 0
    [ 0.040000] SCSI subsystem initialized
    [ 0.041000] usbcore: registered new interface driver usbfs
    [ 0.042000] usbcore: registered new interface driver hub
    [ 0.043000] usbcore: registered new device driver usb
    [ 0.044000] Switching to clocksource wktmr
    [ 0.052000] NET: Registered protocol family 2
    [ 0.057000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    [ 0.064000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    [ 0.071000] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    [ 0.078000] TCP: Hash tables configured (established 16384 bind 16384)
    [ 0.084000] TCP reno registered
    [ 0.088000] UDP hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.093000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.100000] NET: Registered protocol family 1
    [ 0.104000] RPC: Registered named UNIX socket transport module.
    [ 0.110000] RPC: Registered udp transport module.
    [ 0.115000] RPC: Registered tcp transport module.
    [ 0.120000] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [ 0.152000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [ 0.158000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
    [ 0.165000] fuse init (API version 7.1
    [ 0.169000] msgmni has been set to 442
    [ 0.173000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
    [ 0.181000] io scheduler noop registered
    [ 0.185000] io scheduler cfq registered (default)
    [ 0.189000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.203000] console [ttyS0] enabled, bootconsole disabled 62) is a 16550A
    [ 0.203000] console [ttyS0] enabled, bootconsole disabled
    [ 0.214000] serial8250.0: ttyS1 at MMIO 0x10406840 (irq = 63) is a 16550A
    [ 0.221000] serial8250.0: ttyS2 at MMIO 0x10406880 (irq = 64) is a 16550A
    [ 0.234000] brd: module loaded
    [ 0.241000] loop: module loaded
    [ 0.245000] brcmstb_nand: NAND controller driver is loaded
    [ 0.372000] bcmgenet: configuring instance #0 for internal PHY
    [ 0.397000] bcmgenet bcmgenet.0: (unregistered net_device): link down
    [ 0.403000] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
    [ 0.411000] usbcore: registered new interface driver pegasus
    [ 0.417000] usbcore: registered new interface driver asix
    [ 0.422000] usbcore: registered new interface driver cdc_ether
    [ 0.428000] usbcore: registered new interface driver net1080
    [ 0.434000] usbcore: registered new interface driver cdc_subset
    [ 0.440000] usbcore: registered new interface driver zaurus
    [ 0.445000] usbcore: registered new interface driver cdc_ncm
    [ 0.451000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.458000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
    [ 0.463000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
    [ 0.502000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
    [ 0.513000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
    [ 0.519000] hub 1-0:1.0: USB hub found
    [ 0.523000] hub 1-0:1.0: 1 port detected
    [ 0.527000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI
    [ 0.532000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
    [ 0.571000] ehci-brcm ehci-brcm.1: irq 68, io mem 0x10480500
    [ 0.582000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
    [ 0.588000] hub 2-0:1.0: USB hub found
    [ 0.592000] hub 2-0:1.0: 1 port detected
    [ 0.596000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [ 0.602000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
    [ 0.607000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
    [ 0.615000] ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400
    [ 0.686000] hub 3-0:1.0: USB hub found
    [ 0.690000] hub 3-0:1.0: 1 port detected
    [ 0.694000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI
    [ 0.699000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
    [ 0.707000] ohci-brcm ohci-brcm.1: irq 69, io mem 0x10480600
    [ 0.778000] hub 4-0:1.0: USB hub found
    [ 0.782000] hub 4-0:1.0: 1 port detected
    [ 0.786000] Initializing USB Mass Storage driver...
    [ 0.791000] usbcore: registered new interface driver usb-storage
    [ 0.797000] USB Mass Storage support registered.
    [ 0.802000] mousedev: PS/2 mouse device common for all mice
    [ 0.808000] sdhci: Secure Digital Host Controller Interface driver
    [ 0.814000] sdhci: Copyright(c) Pierre Ossman
    [ 0.818000] sdhci-pltfm: SDHCI platform and OF driver helper
    [ 0.824000] sdhci-brcmstb sdhci-brcmstb.0: Enabling controller
    [ 0.835000] mmc0: SDHCI controller on sdhci-brcmstb.0 [sdhci-brcmstb.0] using ADMA
    [ 0.842000] sdhci-brcmstb sdhci-brcmstb.1: Disabled by bootloader
    [ 0.848000] usbcore: registered new interface driver usbhid
    [ 0.854000] usbhid: USB HID core driver
    [ 0.858000] TCP cubic registered
    [ 0.861000] NET: Registered protocol family 17
    [ 0.866000] 8021q: 802.1Q VLAN Support v1.8
    [ 0.870000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor
    [ 0.879000] warning: unable to build a flash partition map, using entire device
    [ 0.886000] EBI CS2: setting up NAND flash (primary)
    [ 0.891000] NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (Toshiba NAND 512MiB 3,3V 8-bit)
    [ 0.900000] brcmnand brcmnand.0: 512MiB total, 256KiB blocks, 4KiB pages, 32B OOB, 8-bit, BCH-24 (1KiB sector)
    [ 0.913000] Bad block table found at page 131008, version 0x01
    [ 0.919000] Bad block table found at page 130944, version 0x01
    [ 0.925000] nand_read_bbt: bad block at 0x000018000000
    [ 0.930000] nand_read_bbt: bad block at 0x000018040000
    [ 0.936000] 3 cmdlinepart partitions found on MTD device brcmnand.0
    [ 0.942000] Creating 3 MTD partitions on "brcmnand.0":
    [ 0.947000] 0x000000000000-0x000001000000 : "Kernel"
    [ 0.958000] 0x000001000000-0x000002000000 : "Kernel2"
    [ 0.966000] 0x000002000000-0x000020000000 : "raw"
    [ 0.973000] EBI CS0: setting up SPI flash
    [ 0.977000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
    [ 0.986000] m25p80 spi0.0: found is25lp032d, expected m25p80
    [ 0.992000] m25p80 spi0.0: is25lp032d (4096 Kbytes)
    [ 0.996000] 6 cmdlinepart partitions found on MTD device spi0.0
    [ 1.002000] Creating 6 MTD partitions on "spi0.0":
    [ 1.007000] 0x000000000000-0x000000100000 : "bootloader"
    [ 1.034000] 0x000000100000-0x000000200000 : "secbootloader"
    [ 1.040000] 0x000000200000-0x000000220000 : "env"
    [ 1.046000] 0x000000220000-0x000000230000 : "nvram"
    [ 1.054000] 0x000000230000-0x000000270000 : "logo"
    [ 1.059000] 0x000000270000-0x000000400000 : "userfs"
    [ 1.066000] UBI: attaching mtd3 to ubi0
    [ 1.070000] UBI: physical eraseblock size: 262144 bytes (256 KiB)
    [ 1.076000] UBI: logical eraseblock size: 253952 bytes
    [ 1.081000] UBI: smallest flash I/O unit: 4096
    [ 1.086000] UBI: VID header offset: 4096 (aligned 4096)
    [ 1.092000] UBI: data offset: 8192
    [ 2.652000] UBI: max. sequence number: 937
    [ 2.666000] UBI: attached mtd3 to ubi0
    [ 2.670000] UBI: MTD device name: "raw"
    [ 2.675000] UBI: MTD device size: 480 MiB
    [ 2.680000] UBI: number of good PEBs: 1914
    [ 2.684000] UBI: number of bad PEBs: 6
    [ 2.689000] UBI: number of corrupted PEBs: 0
    [ 2.693000] UBI: max. allowed volumes: 128
    [ 2.698000] UBI: wear-leveling threshold: 4096
    [ 2.703000] UBI: number of internal volumes: 1
    [ 2.707000] UBI: number of user volumes: 3
    [ 2.712000] UBI: available PEBs: 11
    [ 2.716000] UBI: total number of reserved PEBs: 1903
    [ 2.721000] UBI: number of PEBs reserved for bad PEB handling: 19
    [ 2.727000] UBI: max/mean erase counter: 4/0
    [ 2.732000] UBI: image sequence number: 1082318731
    [ 2.736000] UBI: background thread "ubi_bgt0d" started, PID 44

    [ 2.754000] Freeing unused kernel memory: 4304k freed
    Waited /dev/mtd6 0 ms
    Good digital signature!
    Correct Digital signature
    [ 3.220000] [MAG325]: RDC Scratch regs values. Surf0 [Reg0: 0x07500000, Reg1: 0x07500000], Surf1 [Reg0: 0x06000000]
    [ 3.230000] [MAG325]: GFD picture size regs values. [GFD_0: 0x02d00240, GFD_1: 0x02d00120]
    [ 3.239000] [MAG325]: GFD pitch regs values. [GFD_0: 0x000005a0, GFD_1: 0x00000b40]
    [ 3.246000] Framebuffer [0] Probed display resolution to be (720x576p) pixels.
    [ 3.257000] Framebuffer [1] Probed display resolution to be (720x576i) pixels.
    [ 3.305000] kir: module license 'Dual BSDL/GPL' taints kernel.
    [ 3.310000] Disabling lock debugging due to kernel taint
    [ 3.317000] Initialized KIR1 in NEC mode [input: In0].
    [ 3.322000] Initialized KIR2 in RC-5 mode [input: In0].
    [ 3.327000] input: Infomir generic NEC/RC-5 IR driver as /devices/virtual/input/input0
    Waited spalsh 0 ms
    [ 4.650000] UBIFS: recovery needed
    [ 4.753000] UBIFS: recovery completed
    [ 4.757000] UBIFS: mounted UBI device 0, volume 0, name "Rootfs"
    [ 4.763000] UBIFS: file system size: 225001472 bytes (219728 KiB, 214 MiB, 886 LEBs)
    [ 4.771000] UBIFS: journal size: 9404416 bytes (9184 KiB, 8 MiB, 38 LEBs)
    [ 4.778000] UBIFS: media format: w4/r0 (latest is w4/r0)
    [ 4.784000] UBIFS: default compressor: lzo
    [ 4.788000] UBIFS: reserved for root: 0 bytes (0 KiB)
    Switching root.
    [ 5.044000] kir module unloaded...
    Bad inittab entry at line 24
    starting pid 158, tty '': '/etc/init.d/rcS'
    >>> Mounting virtual filesystems
    >>> Starting splash menu...
    [ 5.453000] Initialized KIR1 in NEC mode [input: In0].
    [ 5.459000] Initialized KIR2 in RC-5 mode [input: In0].
    [ 5.464000] input: Infomir generic NEC/RC-5 IR driver as /devices/virtual/input/input1
    [ 5.548000] [MAG325]: RDC Scratch regs values. Surf0 [Reg0: 0x2f200000, Reg1: 0x2f200000], Surf1 [Reg0: 0x2f200000]
    [ 5.558000] [MAG325]: GFD picture size regs values. [GFD_0: 0x02d00240, GFD_1: 0x02d00120]
    [ 5.567000] [MAG325]: GFD pitch regs values. [GFD_0: 0x000005a0, GFD_1: 0x00000b40]
    [ 5.574000] Framebuffer [0] Probed display resolution to be (720x576p) pixels.
    [ 5.585000] Framebuffer [1] Probed display resolution to be (720x576i) pixels.
    Fast Starting Kernel event manager...
    Error type bmp 0x0.
    [ 5.897000] udevd[215]: starting version 174
    Jan 1 00:00:06 udevd[215]: unknown key 'DEVTYPE' in /etc/udev/rules.d/10-wlan.rules:1

    Jan 1 00:00:06 udevd[215]: unknown key 'DEVTYPE' in /etc/udev/rules.d/10-wlan.rules:2

    Good digital signature!
    Correct Digital signature
    [ 6.610000] UBIFS: recovery needed
    [ 6.734000] UBIFS: recovery completed
    [ 6.738000] UBIFS: mounted UBI device 0, volume 2, name "Userfs"
    [ 6.744000] UBIFS: file system size: 19808256 bytes (19344 KiB, 18 MiB, 78 LEBs)
    [ 6.751000] UBIFS: journal size: 3555328 bytes (3472 KiB, 3 MiB, 14 LEBs)
    [ 6.759000] UBIFS: media format: w4/r0 (latest is w4/r0)
    [ 6.765000] UBIFS: default compressor: lzo
    [ 6.769000] UBIFS: reserved for root: 0 bytes (0 KiB)
    Starting Network Interface Plugging Daemon: eth0.
    Configuring network interfaces: done.

    Fast Replaying boot udev events...
    Done.
    >>> Starting Nexus server
    [ 10.175000] BCMDRV: Initializing bcmdriver version $ 8
    [ 10.181000] BCMDRV: Total intc words=3,Total Irqs=97
    [ 10.186000] BCMDRV: Initialization complete
    cat: can't open '/ram/wifi/curr_driver': No such file or directory
    starting pid 766, tty '': '/bin/cttyhack /bin/login'
    (none) login:
  2. #62
    Senior Member
    Аватар для Dr_Vao
    Регистрация 17.01.2013
    Адрес Soviet Union
    Сообщений 2,059
    Нашел точки UART. Прервать загрузку не дает, в конце просит логин и пароль. Стандартные не подходят.
    Вот лог загрузки:
    BCM07584500
    SLBS... done.
    M0C
    PSSBL. size:00067F40
    DZS
    L2=1
    LLMB=1
    BrCfg=E30FB7C6
    #@

    BCM975839A0 CFE v16.4, Endian Mode: Little
    Build Date: Fri Jan 12 14:08:20 EET 2018 (alever@alever-build)
    Copyright (C) Broadcom Corporation.............
    Даже не знаю, что вам посоветовать.

    01. Искать, как принудительно остановить загрузку, чтобы можно было работать в консоли. (В дальнейшем это очень пригодится).

    02. Попробовать изменить переменные update_url=

    с update_url=igmp://224.50.0.50:3221

    на update_url=http://update.infomir.com/mag/322/imageupdate

    03. Не будет результата, скачивать эту прошивку http://update.infomir.com/mag/322/imageupdate, разбирать ее на составляющие:

    kernel - ядро
    rootfs - файловая система
    env - список переменных
    logo - загрузочный логотип

    (искать описание этого процесса или обратиться к специалистам)

    04. Затем используя оперативную память приставки, залить в НАНД kernel и rootfs

    (на 4ПДА есть инструкция для МАГ-255)

    05. Есть подозрение, что у вас МАГ-325 или МАГ-323

    MAG325/323 — закрытая платформа без возможности модификации образа. Модель интегрирована с системой защиты контента Verimatrix и предназначена для операторов, которые уже используют Verimatrix.

    Удачи...
    Последний раз редактировалось Dr_Vao; 12.09.2018 в 09:33.
  3. #63
    Junior Member
    Регистрация 03.09.2018
    Сообщений 8
    Спасибо, буду дальше ковырять.
  4. #64
    Junior Member
    Регистрация 09.09.2018
    Сообщений 8
    Hello,
    does anyone know where I can find older utilities, especially rootfs, for MAG 322/324? There are some bugs at the new ones and i'd like to try the older ones. Thanks in advance
  5. #65
    Senior Member
    Аватар для Katran
    Регистрация 21.02.2010
    Адрес Germany
    Сообщений 2,035
    Кому в Германии нужен Mag 322 здесь последний за 21.14€ плюс пересылка. Старая цена 62€.
    https://www.mindfactory.de/Highlight...46.33349609375
    Страна: Germany. Пров: Unitmedia 400 Mbit (Kabel). Девайс: LG OLED55C6D, Egreat A5, Mag 351, Dune HD Pro 4K, Nvidia Shield 16GB 2017, Fritz!Box 6490.

  6. #66
    Member
    Регистрация 20.04.2018
    Сообщений 31
    сгорел китайский маг!
    что посоветуете
  7. #67
    Senior Member
    Аватар для SVGalar
    Регистрация 16.04.2015
    Адрес Dnepr
    Сообщений 1,008
    сгорел китайский маг!
    что посоветуете
    Одесский, Инфомировский МАГ или на крайняк Ауру. Но ни как не узкоглазую подделку...
    MAG 254 - MAG 256 - MAG 322
  8. #68
    Junior Member
    Регистрация 25.07.2015
    Сообщений 3
    Здраствуйте нужна помощь маг 322 после прошивки заходит system recovery utility дальше не грузится причем прошивается от туда на другую прошивку как через usb так и multicast но при загрузке выходит сообщение wrong operator key и заходит system recovery utility причем там захожу device information там нет не мас адреса не сирийника
  9. #69
    Junior Member
    Регистрация 26.11.2018
    Сообщений 1
    UART такой же как и в mag250

    2 - 3.3v
    16 - gnd
    18 - tx
    20 - rx
    Вложения
  10. #70
    Junior Member
    Регистрация 30.01.2019
    Сообщений 2
    Здравствуйте! Имею, скорее всего, точно такую же проблему как и у Вас. Поменял mag 250 на mag 322 еще в начале 2018 года и появилась такая же проблема, причем если к той же конфигурации (сетевой кабель, роутер, hdmi кабель) вернуть обратно mag 250 она работает без проблем. Проблема сейчас проявляется только на hd каналах.
    Отдавал mag 322 своему провайдеру на проверку - "с приставкой все нормально".
    Надеялся, что обновления Инфомира со временем устранят проблему, но нет.
    Единственное, чем удалось решить проблему - это поднять на роутере udptohttp proxy и приставку настроить на него. Тогда все каналы sd и hd работают стабильно. Но при настройке на udptohttp proxy появилась проблема с работой timeshift, не всегда становится на паузу, а просто вылетает в список каналов.
    Т.е. для себя я проблему не решил полностью. Не появилось ли у Вас за это время какое-либо еще решение проблемы?

Ваши права

  • Вы не можете создавать новые темы
  • Вы не можете отвечать в темах
  • Вы не можете прикреплять вложения
  • Вы не можете редактировать свои сообщения